Specialty Tools

Tap Socket Set-1

For Use in Restricted Areas. Ideal for use in areas where a T handle won't fit. Set of 8 sockets fits all number and fractional M.C.T.I. standard taps thru 1/2 inch. Also fits 1/8 inch NPT taps and metric taps thru 12mm manufactured to M.C.T.I. standards...

Master Fuel Injection Test Set

Disconnects the Fuel Module on 98 & Later GM Full Size Pickups, Suburban & Tahoe.Two piece design allows access to the connectors. Slide the proper size end into the connector. Rotate and slide the other half in place. Now the module can be disconnected...

Small Engine Ring Compressor. 1-1/2 in to 3 in

The Lisle spring clutch assures a proper fit on the piston and a positive locking action.  

Windshield Molding / Door Handle Clip Pliers

For removing most windshield molding clips and door handle clips. Releases clips to remove chrome molding on most windshields and rear glass. Offset handle permits easy access to molding clips. Slips under door handle without damage to panel material...

Single Spring Brake Tool For GM

Releases Tension on Both Large and Small GM Single Spring Brakes During Servicing.Many GM brakes use a heavy single spring. The 50600 engages the spring and quickly releases the spring tension. The brake can then be disassembled to replace brake shoes,...

Pneumatic Fan Clutch Wrench Set

Quickly Removes & Installs Fan Clutch When Repairing The Water Pump Or Fan Clutch.Does the job much faster and easier than conventional fan clutch wrenches. No holding wrench is necessary. The set includes 7 driving wrenches that fit Ford, GM and...

Handy Hooker Circuit Tester (discontinued-see-w2993)

Hooded Probe Protects Your Fingers and Automatically Centers the Wire.mall size allows easy use even in the tightest places. Quickly test low voltage up to 28 volts. Alligator clip grounds tester. Hooded Probe Protects Your Fingers and Automatically...

10PC Fan Clutch Wrench Set

2-1/4" Fan Pulley Holding Tool2-3/8" Fan Clutch Bolt Holding Tool2-1/8" Fan Clutch Pulley Holding Tool3-1/4" Fan Pulley Holding Tool3" Fan Clutch Pulley Holding Tool2-13/16" Fan Hub Wrench1-7/16" Fan Clutch Nut Wrench1-7/16" Fan Clutch Wrench1-9/16" Fan...

Spindle Nut Wrench Set

Multiple use on 2-Wheel & 4-Wheel drive trucks Includes sockets for removal and installation of 4 x 4 spindles & Toyota locknut wrench Constructed of Vanadium steel Set Includes: -4WD Front Spindle Puller -1/2 - 3/4 Ton 4-Slot 4WD Wheel Bearing Locknut...

Ball Joint Service and Master Adapter set

• Removes and replaces ball joints• C frame press alone can be used to remove and replace universal joints• Set includes all the receiver tubes and removing/installing adapters needed to work on press-fit upper and lower ball joints on...

Wheel Hub Resurfacing Kit

Attacks the rust on lug studs and rotors on the hub assembly faster and easier. Can be used on most domestic and import vehicles with either front or rear disc brakes. Sanding pads attach to the tool with Velcro fasteners. Tool fits your power drill...

Tailpipe Expander

Removes clamp grooves and rounds out pipes. Practical, rugged tools that make easy work of a tough job. Two sizes fit most pipes: 32500 - 1 5/8 inch to 2 7/16 (41.3mm - 61.9mm) and the 32750 - 2 3/8 inch to 3 1/4 inch (60.3mm - 82.5mm).