Specialty Tools

71750 LED QUICK CHANGE TERMINAL TOOL SET (Discontinued) See 95839

Lights the Work Area and Removes Wires from Terminals without Damage. The light handle illuminates electrical connectors. Includes 24 quick-connect ÿterminal disconnect tools, a sheathing ripper and a terminal pin repair tool. Compact handle uses...

82600 CAT III DIGITAL MULTIMETER

Safely and Accurately Test Electrical Systems. Large, Easy to Read LCD Display with Backlight. Measures AC/DC voltage/current up to 600V and 10A,capacitance, diode, duty cycle, frequency, resistance, temperature and transistor. Includes 13 Functions and...

82650 MULTIMETER ACCESSORY KIT

Extend Multimeter Capabilities. Interchangeable probes for a wide range of testing possibilities. Compatible with most multimeters and scopes with standard 4mm connectors. Kit includes 43" long 4mm banana test leads with straight and 90ø connections,...

82660 ALLIGATOR EXTENSION TEST CLIP SET - OBSOLETE AT FACTORY

A Set of 6" Insulated Alligator Clips. Connects to standard 4mm banana test leads for hard-to-reach areas such as under the dash. Strong spring action keeps jaws in contact with the test point. The clip is insulated to help prevent unintentional contact.

12100 OXYGEN SENSOR SOCKET

Removes and Installs Oxygen Sensors on Most Domestic and Some Imports. Specialÿ22mm socket with cutaway slot to provide clearance for wire harness. Provides adequate depth to fit over sensor. Heat-treated alloy steel. Use with 3/8" square drive or 1"...

12230 OXYGEN SENSOR THREAD CHASER

Cleans Threads in Oxygen Sensor Holes. Use with 3/4" hex socket or 3/8" square drive. Size: M18x1.5 Also works on M18x1.5 spark plug threads. IMPORTANT: Use anti-seize.

12390 DUAL DRIVE OXYGEN SENSOR WRENCH

Use with a Breaker Bar to Loosen Stubborn Oxygen Sensors. Tool comes with both 1/2" and 3/8" drive. Attach a 1/2" breaker bar on the end of the tool to initially loosen stuck sensors. Usea 3/8" ratchet on the top for fast removal and installation. Fits...

13000 EXHAUST MANIFOLD SPREADER

For Reinstalling the Manifold on Small Block Chevrolets. A simple way to expand a warped manifold so all bolt holes are accurately aligned. Helps prevent cross-threading of manifold bolts. Works best when used in pairs. Or install before removing...

13200 OIL PRESSURE SWITCH SOCKET

Fits 1" and 1 1/16" Switches Up To 1 5/8" Long. One socket with the correct length to fit 1" and 1 1/16" oil pressure switches (for vehicles equipped with warning lights). 1 7/8" overall height for clearance. Use with 3/8" drive or 1 1/8" hex. ÿ

13250 OIL PRESSURE SWITCH SOCKET

Fits 1 1/16" Switches Up To 2 5/8" Long, Found on Newer GM and Chrysler Vehicles. Fits 1 1/16" oil pressure sending unit (gauge type), found on most all '91 and newer GM vehicles. Also fits '87 and newer Chrysler vehicles with combination light and gauge...

13500 41MM WATER PUMP WRENCH FOR GM 1.6L

Use With 3/8” Square Drive and Short Extension to Easily Adjust and Hold the Water Pump When Replacing or Adjusting Timing Belt. Stubby tool design allows access to timing belt sprocket without interference from vehicle frame. Works on 1.6L engines...

14440 WATER PUMP WRENCH FOR GM NORTHSTAR

Removes & Installs the Water Pump Assembly on GM Northstar 4.0L & 4.6L Engines. Turn the tool with a 1/2" drive ratchet or breaker bar. Angled teeth prevent the tool from slipping. ÿ